home *** CD-ROM | disk | FTP | other *** search
/ HAM Toolkit / HAM Toolkit.iso / text / arrl / gen_2.new < prev    next >
Text File  |  1994-02-09  |  46KB  |  1,457 lines

  1. G4B  Test equipment: oscilloscope; signal tracer; antenna noise
  2. bridge; monitoring oscilloscope; field-strength meters
  3.  
  4. G4B01 (D) 
  5. What item of test equipment contains horizontal- and
  6. vertical-channel amplifiers?
  7. A.  An ohmmeter
  8. B.  A signal generator
  9. C.  An ammeter
  10. D.  An oscilloscope
  11.  
  12. G4B02 (D) 
  13. How would a signal tracer normally be used?
  14. A.  To identify the source of radio transmissions
  15. B.  To make exact drawings of signal waveforms
  16. C.  To show standing wave patterns on open-wire feed lines
  17. D.  To identify an inoperative stage in a receiver
  18.  
  19. G4B03 (B) 
  20. Why would you use an antenna noise bridge?
  21. A.  To measure the noise figure of an antenna or other electrical
  22. circuit
  23. B.  To measure the impedance of an antenna or other electrical
  24. circuit
  25. C.  To cancel electrical noise picked up by an antenna
  26. D.  To tune out noise in a receiver
  27.  
  28. G4B04 (C) 
  29. How is an antenna noise bridge normally used?
  30. A.  It is connected at an antenna's feed point and reads the
  31. antenna's noise figure
  32. B.  It is connected between a transmitter and an antenna and is
  33. tuned for minimum SWR
  34. C.  It is connected between a receiver and an unknown impedance
  35. and is tuned for minimum noise
  36. D.  It is connected between an antenna and ground and is tuned
  37. for minimum SWR
  38.  
  39. G4B05 (A) 
  40. What is the best instrument to use to check the signal quality of
  41. a CW or single-sideband phone transmitter?
  42. A.  A monitoring oscilloscope
  43. B.  A field-strength meter
  44. C.  A sidetone monitor
  45. D.  A signal tracer and an audio amplifier
  46.  
  47. G4B06 (D) 
  48. What signal source is connected to the vertical input of a
  49. monitoring oscilloscope when checking the quality of a
  50. transmitted signal?
  51. A.  The IF output of a monitoring receiver
  52. B.  The audio input of the transmitter
  53. C.  The RF signals of a nearby receiving antenna
  54. D.  The RF output of the transmitter
  55.  
  56. G4B07 (A) 
  57. What instrument can be used to determine the horizontal radiation
  58. pattern of an antenna?
  59. A.  A field-strength meter
  60. B.  A grid-dip meter
  61. C.  An oscilloscope
  62. D.  A signal tracer and an audio amplifier
  63.  
  64. G4B08 (C)
  65. How is a field-strength meter normally used?
  66. A.  To determine the standing-wave ratio on a transmission line
  67. B.  To check the output modulation of a transmitter
  68. C.  To monitor relative RF output
  69. D.  To increase average transmitter output
  70.  
  71. G4B09 (A) 
  72. What simple instrument may be used to monitor relative RF output
  73. during antenna and transmitter adjustments?
  74. A.  A field-strength meter
  75. B.  An antenna noise bridge
  76. C.  A multimeter
  77. D.  A metronome
  78.  
  79. G4B10 (B) 
  80. If the power output of a transmitter is increased by four times,
  81. how might a nearby receiver's S-meter reading change?
  82. A.  Decrease by approximately one S unit
  83. B.  Increase by approximately one S unit
  84. C.  Increase by approximately four S units
  85. D.  Decrease by approximately four S units
  86.  
  87. G4B11 (C) 
  88. By how many times must the power output of a transmitter be
  89. increased to raise the S-meter reading on a nearby receiver from
  90. S8 to S9?
  91. A.  Approximately 2 times
  92. B.  Approximately 3 times
  93. C.  Approximately 4 times
  94. D.  Approximately 5 times
  95.  
  96. G4C  Audio rectification in consumer electronics, RF ground
  97.  
  98. G4C01 (B) 
  99. What devices would you install to reduce or eliminate
  100. audio-frequency interference to home-entertainment systems?
  101. A.  Bypass inductors
  102. B.  Bypass capacitors
  103. C.  Metal-oxide varistors
  104. D.  Bypass resistors
  105.  
  106. G4C02 (B) 
  107. What should be done if a properly operating amateur station is
  108. the cause of interference to a nearby telephone?
  109. A.  Make internal adjustments to the telephone equipment
  110. B.  Ask the telephone company to install RFI filters
  111. C.  Stop transmitting whenever the telephone is in use
  112. D.  Ground and shield the local telephone distribution amplifier
  113.  
  114. G4C03 (C) 
  115. What sound is heard from a public-address system if audio
  116. rectification of a nearby single-sideband phone transmission
  117. occurs?
  118. A.  A steady hum whenever the transmitter's carrier is on the air
  119. B.  On-and-off humming or clicking
  120. C.  Distorted speech from the transmitter's signals
  121. D.  Clearly audible speech from the transmitter's signals
  122.  
  123. G4C04 (A) 
  124. What sound is heard from a public-address system if audio
  125. rectification of a nearby CW transmission occurs?
  126. A.  On-and-off humming or clicking
  127. B.  Audible, possibly distorted speech
  128. C.  Muffled, severely distorted speech
  129. D.  A steady whistling
  130.  
  131. G4C05 (C) 
  132. How can you minimize the possibility of audio rectification of
  133. your transmitter's signals?
  134. A.  By using a solid-state transmitter
  135. B.  By using CW emission only
  136. C.  By ensuring that all station equipment is properly grounded
  137. D.  By installing bypass capacitors on all power supply
  138. rectifiers
  139.  
  140. G4C06 (D) 
  141. If your third-floor amateur station has a ground wire running 33
  142. feet down to a ground rod, why might you get an RF burn if you
  143. touch the front panel of your HF transceiver?
  144. A.  Because the ground rod is not making good contact with moist
  145. earth
  146. B.  Because the transceiver's heat-sensing circuit is not working
  147. to start the cooling fan
  148. C.  Because of a bad antenna connection, allowing the RF energy
  149. to take an easier path out of the transceiver through you
  150. D.  Because the ground wire is a resonant length on several HF
  151. bands and acts more like an antenna than an RF ground connection
  152.  
  153. G4C07 (A) 
  154. What is NOT an important reason to have a good station ground?
  155. A.  To reduce the cost of operating a station
  156. B.  To reduce electrical noise
  157. C.  To reduce interference
  158. D.  To reduce the possibility of electric shock
  159.  
  160. G4C08 (A) 
  161. What is one good way to avoid stray RF energy in your amateur
  162. station?
  163. A.  Keep the station's ground wire as short as possible
  164. B.  Use a beryllium ground wire for best conductivity
  165. C.  Drive the ground rod at least 14 feet into the ground
  166. D.  Make a couple of loops in the ground wire where it connects
  167. to your station
  168.  
  169. G4C09 (B) 
  170. Which statement about station grounding is NOT true?
  171. A.  Braid from RG-213 coaxial cable makes a good conductor to tie
  172. station equipment together into a station ground
  173. B.  Only transceivers and power amplifiers need to be tied into a
  174. station ground
  175. C.  According to the National Electrical Code, there should be
  176. only one grounding system in a building
  177. D.  The minimum length for a good ground rod is 8 feet
  178.  
  179. G4C10 (C) 
  180. Which statement about station grounding is true?
  181. A.  The chassis of each piece of station equipment should be tied
  182. together with high-impedance conductors
  183. B.  If the chassis of all station equipment is connected with a
  184. good conductor, there is no need to tie them to an earth ground
  185. C.  RF hot spots can occur in a station located above the ground
  186. floor if the equipment is grounded by a long ground wire
  187. D.  A ground loop is an effective way to ground station equipment
  188.  
  189. G4C11 (D) 
  190. Which of the following is NOT covered in the National Electrical
  191. Code?
  192. A.  Minimum conductor sizes for different lengths of amateur
  193. antennas
  194. B.  The size and composition of grounding conductors
  195. C.  Electrical safety inside the ham shack
  196. D.  The RF exposure limits of the human body
  197.  
  198. G4D  Speech processors; PEP calculations; wire sizes and fuses
  199.  
  200. G4D01 (D) 
  201. What is the reason for using a properly adjusted speech processor
  202. with a single-sideband phone transmitter?
  203. A.  It reduces average transmitter power requirements
  204. B.  It reduces unwanted noise pickup from the microphone
  205. C.  It improves voice frequency fidelity
  206. D.  It improves signal intelligibility at the receiver
  207.  
  208. G4D02 (B) 
  209. If a single-sideband phone transmitter is 100% modulated, what
  210. will a speech processor do to the transmitter's power?
  211. A.  It will increase the output PEP
  212. B.  It will add nothing to the output PEP
  213. C.  It will decrease the peak power output
  214. D.  It will decrease the average power output
  215.  
  216. G4D03 (B) 
  217. How is the output PEP of a transmitter calculated if an
  218. oscilloscope is used to measure the transmitter's peak load
  219. voltage across a resistive load?
  220. A.  PEP = [(Vp)(Vp)] / (RL)
  221. B.  PEP = [(0.707 PEV)(0.707 PEV)] / RL
  222. C.  PEP = (Vp)(Vp)(RL)
  223. D.  PEP = [(1.414 PEV)(1.414 PEV)] / RL
  224.  
  225. G4D04 (A) 
  226. What is the output PEP from a transmitter if an oscilloscope
  227. measures 200 volts peak-to-peak across a 50-ohm resistor
  228. connected to the transmitter output?
  229. A.  100 watts
  230. B.  200 watts
  231. C.  400 watts
  232. D.  1000 watts
  233.  
  234. G4D05 (B) 
  235. What is the output PEP from a transmitter if an oscilloscope
  236. measures 500 volts peak-to-peak across a 50-ohm resistor
  237. connected to the transmitter output?
  238. A.  500 watts
  239. B.  625 watts
  240. C.  1250 watts
  241. D.  2500 watts
  242.  
  243. G4D06 (B) 
  244. What is the output PEP of an unmodulated carrier transmitter if
  245. an average-reading wattmeter connected to the transmitter output
  246. indicates 1060 watts?
  247. A.  530 watts
  248. B.  1060 watts
  249. C.  1500 watts
  250. D.  2120 watts
  251.  
  252. G4D07 (A) 
  253. Which wires in a four-conductor line cord should be attached to
  254. fuses in a 240-VAC primary (single phase) power supply?
  255. A.  Only the "hot" (black and red) wires
  256. B.  Only the "neutral" (white) wire
  257. C.  Only the ground (bare) wire
  258. D.  All wires
  259.  
  260. G4D08 (A) 
  261. What size wire is normally used on a 15-ampere, 120-VAC household
  262. lighting circuit?
  263. A.  AWG number 14
  264. B.  AWG number 16
  265. C.  AWG number 18
  266. D.  AWG number 22
  267.  
  268. G4D09 (D) 
  269. What size wire is normally used on a 20-ampere, 120-VAC household
  270. appliance circuit?
  271. A.  AWG number 20
  272. B.  AWG number 16
  273. C.  AWG number 14
  274. D.  AWG number 12
  275.  
  276. G4D10 (D) 
  277. What maximum size fuse or circuit breaker should be used in a
  278. household appliance circuit using AWG number 12 wiring?
  279. A.  100 amperes
  280. B.  60 amperes
  281. C.  30 amperes
  282. D.  20 amperes
  283.  
  284. G4D11 (A) 
  285. What maximum size fuse or circuit breaker should be used in a
  286. household appliance circuit using AWG number 14 wiring?
  287. A.  15 amperes
  288. B.  20 amperes
  289. C.  30 amperes
  290. D.  60 amperes
  291.  
  292. G4E  RF safety
  293.  
  294. G4E01 (A) 
  295. Depending on the wavelength of the signal, the energy density of
  296. the RF field, and other factors, in what way can RF energy affect
  297. body tissue?
  298. A.  It heats the tissue
  299. B.  It causes radiation poisoning
  300. C.  It causes blood flow to stop
  301. D.  It produces genetic changes in the tissue
  302.  
  303. G4E02 (C) 
  304. If you operate your amateur station with indoor antennas, what
  305. precautions should you take when you install them?
  306. A.  Locate the antennas close to your operating position to
  307. minimize feed-line length
  308. B.  Position the antennas along the edge of a wall where it meets
  309. the floor or ceiling to reduce parasitic radiation
  310. C.  Locate the antennas as far away as possible from living
  311. spaces that will be occupied while you are operating
  312. D.  Position the antennas parallel to electrical power wires to
  313. take advantage of parasitic effects
  314.  
  315. G4E03 (A) 
  316. What precaution should you take whenever you make adjustments to
  317. the feed system of a parabolic dish antenna?
  318. A.  Be sure no one can activate the transmitter
  319. B.  Disconnect the antenna-positioning mechanism
  320. C.  Point the dish away from the sun so it doesn't concentrate
  321. solar energy on you
  322. D.  Be sure you and the antenna structure are properly grounded
  323.  
  324. G4E04 (B) 
  325. What is one important thing to consider when using an indoor
  326. antenna?
  327. A.  Use stranded wire to reduce stray RF
  328. B.  Ensure that the antenna is as far away from people as
  329. possible
  330. C.  Use only a Yagi antenna to direct the signals away from
  331. people
  332. D.  Use as much power as possible to ensure that your signal gets
  333. out
  334.  
  335. G4E05 (A) 
  336. Why should a protective fence be placed around the base of a
  337. ground-mounted parabolic dish transmitting antenna?
  338. A.  To reduce the possibility of persons being harmed by RF
  339. energy during transmissions
  340. B.  To reduce the possibility that animals will damage the
  341. antenna
  342. C.  To increase the property value through increased security
  343. awareness
  344. D.  To protect the antenna from lightning damage and provide a
  345. good ground system for the installation
  346.  
  347. G4E06 (B) 
  348. What RF-safety precautions should you take before beginning
  349. repairs on an antenna?
  350. A.  Be sure you and the antenna structure are grounded
  351. B.  Be sure to turn off the transmitter and disconnect the feed
  352. line
  353. C.  Inform your neighbors so they are aware of your intentions
  354. D.  Turn off the main power switch in your house
  355.  
  356. G4E07 (D) 
  357. What precaution should you take when installing a ground-mounted
  358. antenna?
  359. A.  It should not be installed higher than you can reach
  360. B.  It should not be installed in a wet area
  361. C.  It should be painted so people or animals do not accidentally
  362. run into it
  363. D.  It should be installed so no one can come in contact with it
  364.  
  365. G4E08 (B) 
  366. What precautions should you take before beginning repairs on a
  367. microwave feed horn or waveguide?
  368. A.  Be sure to wear tight-fitting clothes and gloves to protect
  369. your body and hands from sharp edges
  370. B.  Be sure the transmitter is turned off and the power source is
  371. disconnected
  372. C.  Be sure the weather is dry and sunny
  373. D.  Be sure propagation conditions are unfavorable for
  374. tropospheric ducting
  375.  
  376. G4E09 (D) 
  377. Why should directional high-gain antennas be mounted higher than
  378. nearby structures?
  379. A.  So they will be dried by the wind after a heavy rain storm
  380. B.  So they will not damage nearby structures with RF energy
  381. C.  So they will receive more sky waves and fewer ground waves
  382. D.  So they will not direct RF energy toward people in nearby
  383. structures
  384.  
  385. G4E10 (C) 
  386. For best RF safety, where should the ends and center of a dipole
  387. antenna be located?
  388. A.  Near or over moist ground so RF energy will be radiated away
  389. from the ground
  390. B.  As close to the transmitter as possible so RF energy will be
  391. concentrated near the transmitter
  392. C.  As high as possible to prevent people from coming in contact
  393. with the antenna
  394. D.  Close to the ground so simple adjustments can be easily made
  395. without climbing a ladder
  396.  
  397. G4E11 (B) 
  398. Which property of RF energy is NOT important in estimating the
  399. energy's effect on body tissue?
  400. A.  The polarization
  401. B.  The critical angle
  402. C.  The power density
  403. D.  The frequency
  404.  
  405. SUBELEMENT G5 - ELECTRICAL PRINCIPLES [2 exam questions - 2
  406. groups]
  407.  
  408. G5A  Impedance, including matching; resistance, including ohm;
  409. reactance, inductance, capacitance and metric divisions of these
  410. values
  411.  
  412. G5A01 (C) 
  413. What is impedance?
  414. A.  The electric charge stored by a capacitor
  415. B.  The opposition to the flow of AC in a circuit containing only
  416. capacitance
  417. C.  The opposition to the flow of AC in a circuit
  418. D.  The force of repulsion between one electric field and another
  419. with the same charge
  420.  
  421. G5A02 (B) 
  422. What is reactance?
  423. A.  Opposition to DC caused by resistors
  424. B.  Opposition to AC caused by inductors and capacitors
  425. C.  A property of ideal resistors in AC circuits
  426. D.  A large spark produced at switch contacts when an inductor is
  427. de-energized
  428.  
  429. G5A03 (D) 
  430. In an inductor, what causes opposition to the flow of AC?
  431. A.  Resistance
  432. B.  Reluctance
  433. C.  Admittance
  434. D.  Reactance
  435.  
  436. G5A04 (C) 
  437. In a capacitor, what causes opposition to the flow of AC?
  438. A.  Resistance
  439. B.  Reluctance
  440. C.  Reactance
  441. D.  Admittance
  442.  
  443. G5A05 (D) 
  444. How does a coil react to AC?
  445. A.  As the frequency of the applied AC increases, the reactance
  446. decreases
  447. B.  As the amplitude of the applied AC increases, the reactance
  448. increases
  449. C.  As the amplitude of the applied AC increases, the reactance
  450. decreases
  451. D.  As the frequency of the applied AC increases, the reactance
  452. increases
  453.  
  454. G5A06 (A) 
  455. How does a capacitor react to AC?
  456. A.  As the frequency of the applied AC increases, the reactance
  457. decreases
  458. B.  As the frequency of the applied AC increases, the reactance
  459. increases
  460. C.  As the amplitude of the applied AC increases, the reactance
  461. increases
  462. D.  As the amplitude of the applied AC increases, the reactance
  463. decreases
  464.  
  465. G5A07 (A) 
  466. When will a power source deliver maximum output to the load?
  467. A.  When the impedance of the load is equal to the impedance of
  468. the source
  469. B.  When the load resistance is infinite
  470. C.  When the power-supply fuse rating equals the primary winding
  471. current
  472. D.  When air wound transformers are used instead of iron-core
  473. transformers
  474.  
  475. G5A08 (D) 
  476. What happens when the impedance of an electrical load is equal to
  477. the internal impedance of the power source?
  478. A.  The source delivers minimum power to the load
  479. B.  The electrical load is shorted
  480. C.  No current can flow through the circuit
  481. D.  The source delivers maximum power to the load
  482.  
  483. G5A09 (A) 
  484. Why is impedance matching important?
  485. A.  So the source can deliver maximum power to the load
  486. B.  So the load will draw minimum power from the source
  487. C.  To ensure that there is less resistance than reactance in the
  488. circuit
  489. D.  To ensure that the resistance and reactance in the circuit
  490. are equal
  491.  
  492. G5A10 (B) 
  493. What unit is used to measure reactance?
  494. A.  Mho
  495. B.  Ohm
  496. C.  Ampere
  497. D.  Siemens
  498.  
  499. G5A11 (B) 
  500. What unit is used to measure impedance?
  501. A.  Volt
  502. B.  Ohm
  503. C.  Ampere
  504. D.  Watt
  505.  
  506. G5B  Decibel, Ohm's Law, current and voltage dividers, electrical
  507. power calculations and series and parallel components,
  508. transformers (either voltage or impedance), sine wave
  509. root-mean-square (RMS) value
  510.  
  511. G5B01 (B) 
  512. A two-times increase in power results in a change of how many dB?
  513. A.  1 dB higher
  514. B.  3 dB higher
  515. C.  6 dB higher
  516. D.  12 dB higher
  517.  
  518. G5B02 (B) 
  519. How can you decrease your transmitter's power by 3 dB?
  520. A.  Divide the original power by 1.5
  521. B.  Divide the original power by 2
  522. C.  Divide the original power by 3
  523. D.  Divide the original power by 4
  524.  
  525. G5B03  (D)
  526. How can you increase your transmitter's power by 6 dB?
  527. A.  Multiply the original power by 1.5
  528. B.  Multiply the original power by 2
  529. C.  Multiply the original power by 3
  530. D.  Multiply the original power by 4
  531.  
  532. G5B04 (C) 
  533. If a signal-strength report is "10 dB over S9", what should the
  534. report be if the transmitter power is reduced from 1500 watts to
  535. 150 watts?
  536. A.  S5
  537. B.  S7
  538. C.  S9
  539. D.  S9 plus 5 dB
  540.  
  541. G5B05 (C) 
  542. If a signal-strength report is "20 dB over S9", what should the
  543. report be if the transmitter power is reduced from 1500 watts to
  544. 15 watts?
  545. A.  S5
  546. B.  S7
  547. C.  S9
  548. D.  S9 plus 10 dB
  549.  
  550. G5B06 (D) 
  551. If a 1.0-ampere current source is connected to two
  552. parallel-connected 10-ohm resistors, how much current passes
  553. through each resistor?
  554. A.  10 amperes
  555. B.  2 amperes
  556. C.  1 ampere
  557. D.  0.5 ampere
  558.  
  559. G5B07 (B) 
  560. In a parallel circuit with a voltage source and several branch
  561. resistors, how is the total current related to the current in the
  562. branch resistors?
  563. A.  It equals the average of the branch current through each
  564. resistor
  565. B.  It equals the sum of the branch current through each resistor
  566. C.  It decreases as more parallel resistors are added to the
  567. circuit
  568. D.  It is the sum of each resistor's voltage drop multiplied by
  569. the total number of resistors
  570.  
  571. G5B08 (B) 
  572. How many watts of electrical power are used if 400 VDC is
  573. supplied to an 800-ohm load?
  574. A.  0.5 watts
  575. B.  200 watts
  576. C.  400 watts
  577. D.  320,000 watts
  578.  
  579. G5B09 (D) 
  580. How many watts of electrical power are used by a 12-VDC light
  581. bulb that draws 0.2 amperes?
  582. A.  60 watts
  583. B.  24 watts
  584. C.  6 watts
  585. D.  2.4 watts
  586.  
  587. G5B10  (A)
  588. How many watts are being dissipated when 7.0 milliamperes flow
  589. through 1.25 kilohms?
  590. A.  Approximately 61 milliwatts
  591. B.  Approximately 39 milliwatts
  592. C.  Approximately 11 milliwatts
  593. D.  Approximately 9 milliwatts
  594.  
  595. G5B11 (C) 
  596. What is the voltage across a 500-turn secondary winding in a
  597. transformer if the 2250-turn primary is connected to 120 VAC?
  598. A.  2370 volts
  599. B.  540 volts
  600. C.  26.7 volts
  601. D.  5.9 volts
  602.  
  603. G5B12 (A) 
  604. What is the turns ratio of a transformer to match an audio
  605. amplifier having a 600-ohm output impedance to a speaker having a
  606. 4-ohm impedance?
  607. A.  12.2 to 1
  608. B.  24.4 to 1
  609. C.  150 to 1
  610. D.  300 to 1
  611.  
  612. G5B13 (D) 
  613. What is the impedance of a speaker that requires a transformer
  614. with a turns ratio of 24 to 1 to match an audio amplifier having
  615. an output impedance of 2000 ohms?
  616. A.  576 ohms
  617. B.  83.3 ohms
  618. C.  7.0 ohms
  619. D.  3.5 ohms
  620.  
  621. G5B14 (B) 
  622. A DC voltage equal to what value of an applied sine-wave AC
  623. voltage would produce the same amount of heat over time in a
  624. resistive element?
  625. A.  The peak-to-peak value
  626. B.  The RMS value
  627. C.  The average value
  628. D.  The peak value
  629.  
  630. G5B15 (D) 
  631. What is the peak-to-peak voltage of a sine wave that has an RMS
  632. voltage of 120 volts?
  633. A.  84.8 volts
  634. B.  169.7 volts
  635. C.  204.8 volts
  636. D.  339.4 volts
  637.  
  638. G5B16 (B) 
  639. A sine wave of 17 volts peak is equivalent to how many volts RMS?
  640. A.  8.5 volts
  641. B.  12 volts
  642. C.  24 volts
  643. D.  34 volts
  644.  
  645. SUBELEMENT G6 - CIRCUIT COMPONENTS [1 exam question - 1 group]
  646.  
  647. G6A  Resistors, capacitors, inductors, rectifiers and
  648. transistors, etc.
  649.  
  650. G6A01 (C) 
  651. If a carbon resistor's temperature is increased, what will happen
  652. to the resistance?
  653. A.  It will increase by 20% for every 10 degrees centigrade
  654. B.  It will stay the same
  655. C.  It will change depending on the resistor's temperature
  656. coefficient rating
  657. D.  It will become time dependent
  658.  
  659. G6A02 (D) 
  660. What type of capacitor is often used in power-supply circuits to
  661. filter the rectified AC?
  662. A.  Disc ceramic
  663. B.  Vacuum variable
  664. C.  Mica
  665. D.  Electrolytic
  666.  
  667. G6A03 (D) 
  668. What type of capacitor is used in power-supply circuits to filter
  669. transient voltage spikes across the transformer's secondary
  670. winding?
  671. A.  High-value
  672. B.  Trimmer
  673. C.  Vacuum variable
  674. D.  Suppressor
  675.  
  676. G6A04 (B) 
  677. Where is the source of energy connected in a transformer?
  678. A.  To the secondary winding
  679. B.  To the primary winding
  680. C.  To the core
  681. D.  To the plates
  682.  
  683. G6A05 (A) 
  684. If no load is attached to the secondary winding of a transformer,
  685. what is current in the primary winding called?
  686. A.  Magnetizing current
  687. B.  Direct current
  688. C.  Excitation current
  689. D.  Stabilizing current
  690.  
  691. G6A06 (C) 
  692. What is the peak-inverse-voltage rating of a power-supply
  693. rectifier?
  694. A.  The maximum transient voltage the rectifier will handle in
  695. the conducting direction
  696. B.  1.4 times the AC frequency
  697. C.  The maximum voltage the rectifier will handle in the
  698. non-conducting direction
  699. D.  2.8 times the AC frequency
  700.  
  701. G6A07 (A) 
  702. What are the two major ratings that must not be exceeded for
  703. silicon-diode rectifiers used in power-supply circuits?
  704. A.  Peak inverse voltage; average forward current
  705. B.  Average power; average voltage
  706. C.  Capacitive reactance; avalanche voltage
  707. D.  Peak load impedance; peak voltage
  708.  
  709. G6A08 (A) 
  710. Why should a resistor and capacitor be wired in parallel with
  711. power-supply rectifier diodes?
  712. A.  To equalize voltage drops and guard against transient voltage
  713. spikes
  714. B.  To ensure that the current through each diode is about the
  715. same
  716. C.  To smooth the output waveform
  717. D.  To decrease the output voltage
  718.  
  719. G6A09 (A) 
  720. What is the output waveform of an unfiltered full-wave rectifier
  721. connected to a resistive load?
  722. A.  A series of pulses at twice the frequency of the AC input
  723. B.  A series of pulses at the same frequency as the AC input
  724. C.  A sine wave at half the frequency of the AC input
  725. D.  A steady DC voltage
  726.  
  727. G6A10 (B) 
  728. A half-wave rectifier conducts during how many degrees of each
  729. cycle?
  730. A.  90 degrees
  731. B.  180 degrees
  732. C.  270 degrees
  733. D.  360 degrees
  734.  
  735. G6A11 (D) 
  736. A full-wave rectifier conducts during how many degrees of each
  737. cycle?
  738. A.  90 degrees
  739. B.  180 degrees
  740. C.  270 degrees
  741. D.  360 degrees
  742.  
  743. SUBELEMENT G7 - PRACTICAL CIRCUITS [1 exam question - 1 group]
  744.  
  745. G7A  Power supplies and filters; single-sideband transmitters and
  746. receivers
  747.  
  748. G7A01 (B) 
  749. What safety feature does a power-supply bleeder resistor provide?
  750. A.  It improves voltage regulation
  751. B.  It discharges the filter capacitors
  752. C.  It removes shock hazards from the induction coils
  753. D.  It eliminates ground-loop current
  754.  
  755. G7A02 (A) 
  756. Where is a power-supply bleeder resistor connected?
  757. A.  Across the filter capacitor
  758. B.  Across the power-supply input
  759. C.  Between the transformer primary and secondary windings
  760. D.  Across the inductor in the output filter
  761.  
  762. G7A03 (D) 
  763. What components are used in a power-supply filter network?
  764. A.  Diodes
  765. B.  Transformers and transistors
  766. C.  Quartz crystals
  767. D.  Capacitors and inductors
  768.  
  769. G7A04 (D) 
  770. What should be the peak-inverse-voltage rating of the rectifier
  771. in a full-wave power supply?
  772. A.  One-quarter the normal output voltage of the power supply
  773. B.  Half the normal output voltage of the power supply
  774. C.  Equal to the normal output voltage of the power supply
  775. D.  Double the normal peak output voltage of the power supply
  776.  
  777. G7A05 (D) 
  778. What should be the peak-inverse-voltage rating of the rectifier
  779. in a half-wave power supply?
  780. A.  One-quarter to one-half the normal peak output voltage of the
  781. power supply
  782. B.  Half the normal output voltage of the power supply
  783. C.  Equal to the normal output voltage of the power supply
  784. D.  One to two times the normal peak output voltage of the power
  785. supply
  786.  
  787. G7A06 (B) 
  788. What should be the impedance of a low-pass filter as compared to
  789. the impedance of the transmission line into which it is inserted?
  790. A.  Substantially higher
  791. B.  About the same
  792. C.  Substantially lower
  793. D.  Twice the transmission line impedance
  794.  
  795. G7A07 (B) 
  796. In a typical single-sideband phone transmitter, what circuit
  797. processes signals from the balanced modulator and sends signals
  798. to the mixer?
  799. A.  Carrier oscillator
  800. B.  Filter
  801. C.  IF amplifier
  802. D.  RF amplifier
  803.  
  804. G7A08 (D) 
  805. In a single-sideband phone transmitter, what circuit processes
  806. signals from the carrier oscillator and the speech amplifier and
  807. sends signals to the filter?
  808. A.  Mixer
  809. B.  Detector
  810. C.  IF amplifier
  811. D.  Balanced modulator
  812.  
  813. G7A09 (C) 
  814. In a single-sideband phone superheterodyne receiver, what circuit
  815. processes signals from the RF amplifier and the local oscillator
  816. and sends signals to the IF filter?
  817. A.  Balanced modulator
  818. B.  IF amplifier
  819. C.  Mixer
  820. D.  Detector
  821.  
  822. G7A10 (D) 
  823. In a single-sideband phone superheterodyne receiver, what circuit
  824. processes signals from the IF amplifier and the BFO and sends
  825. signals to the AF amplifier?
  826. A.  RF oscillator
  827. B.  IF filter
  828. C.  Balanced modulator
  829. D.  Detector
  830.  
  831. G7A11 (B) 
  832. In a single-sideband phone superheterodyne receiver, what circuit
  833. processes signals from the IF filter and sends signals to the
  834. detector?
  835. A.  RF oscillator
  836. B.  IF amplifier
  837. C.  Mixer
  838. D.  BFO
  839.  
  840. SUBELEMENT G8 - SIGNALS AND EMISSIONS [2 exam questions - 2
  841. groups]
  842.  
  843. G8A  Signal information, AM, FM, single and double sideband and
  844. carrier, bandwidth, modulation envelope, deviation,
  845. overmodulation
  846.  
  847. G8A01 (D) 
  848. What type of modulation system changes the amplitude of an RF
  849. wave for the purpose of conveying information?
  850. A.  Frequency modulation
  851. B.  Phase modulation
  852. C.  Amplitude-rectification modulation
  853. D.  Amplitude modulation
  854.  
  855. G8A02 (B) 
  856. What type of modulation system changes the phase of an RF wave
  857. for the purpose of conveying information?
  858. A.  Pulse modulation
  859. B.  Phase modulation
  860. C.  Phase-rectification modulation
  861. D.  Amplitude modulation
  862.  
  863. G8A03 (D) 
  864. What type of modulation system changes the frequency of an RF
  865. wave for the purpose of conveying information?
  866. A.  Phase-rectification modulation
  867. B.  Frequency-rectification modulation
  868. C.  Amplitude modulation
  869. D.  Frequency modulation
  870.  
  871. G8A04 (B) 
  872. What emission is produced by a reactance modulator connected to
  873. an RF power amplifier?
  874. A.  Multiplex modulation
  875. B.  Phase modulation
  876. C.  Amplitude modulation
  877. D.  Pulse modulation
  878.  
  879. G8A05 (D) 
  880. what emission type does the instantaneous amplitude (envelope)
  881. of the RF signal vary in accordance with the modulating audio?
  882. A.  Frequency shift keying
  883. B.  Pulse modulation
  884. C.  Frequency modulation
  885. D.  Amplitude modulation
  886.  
  887. G8A06 (C) 
  888. How much is the carrier suppressed below peak output power in a
  889. single-sideband phone transmission?
  890. A.  No more than 20 dB
  891. B.  No more than 30 dB
  892. C.  At least 40 dB
  893. D.  At least 60 dB
  894.  
  895. G8A07 (C) 
  896. What is one advantage of carrier suppression in a double-sideband
  897. phone transmission?
  898. A.  Only half the bandwidth is required for the same information
  899. content
  900. B.  Greater modulation percentage is obtainable with lower
  901. distortion
  902. C.  More power can be put into the sidebands
  903. D.  Simpler equipment can be used to receive a double-sideband
  904. suppressed-carrier signal
  905.  
  906. G8A08 (A) 
  907. Which popular phone emission uses the narrowest frequency
  908. bandwidth?
  909. A.  Single-sideband
  910. B.  Double-sideband
  911. C.  Phase-modulated
  912. D.  Frequency-modulated
  913.  
  914. G8A09 (D) 
  915. What happens to the signal of an overmodulated single-sideband or
  916. double-sideband phone transmitter?
  917. A.  It becomes louder with no other effects
  918. B.  It occupies less bandwidth with poor high-frequency response
  919. C.  It has higher fidelity and improved signal-to-noise ratio
  920. D.  It becomes distorted and occupies more bandwidth
  921.  
  922. G8A10 (B) 
  923. How should the microphone gain control be adjusted on a
  924. single-sideband phone transmitter?
  925. A.  For full deflection of the ALC meter on modulation peaks
  926. B.  For slight movement of the ALC meter on modulation peaks
  927. C.  For 100% frequency deviation on modulation peaks
  928. D.  For a dip in plate current
  929.  
  930. G8A11 (C)
  931. What is meant by flattopping in a single-sideband phone
  932. transmission?
  933. A.  Signal distortion caused by insufficient collector current
  934. B.  The transmitter's automatic level control is properly
  935. adjusted
  936. C.  Signal distortion caused by excessive drive
  937. D.  The transmitter's carrier is properly suppressed
  938.  
  939. G8B  Frequency mixing, multiplication, bandwidths, HF data
  940. communications
  941.  
  942. G8B01 (A) 
  943. What receiver stage combines a 14.25-MHz input signal with a
  944. 13.795-MHz oscillator signal to produce a 455-kHz intermediate
  945. frequency (IF) signal?
  946. A.  Mixer
  947. B.  BFO
  948. C.  VFO
  949. D.  Multiplier
  950.  
  951. G8B02 (B) 
  952. If a receiver mixes a 13.800-MHz VFO with a 14.255-MHz received
  953. signal to produce a 455-kHz intermediate frequency (IF) signal,
  954. what type of interference will a 13.345-MHz signal produce in the
  955. receiver?
  956. A.  Local oscillator
  957. B.  Image response
  958. C.  Mixer interference
  959. D.  Intermediate interference
  960.  
  961. G8B03 (A) 
  962. What stage in a transmitter would change a 5.3-MHz input signal
  963. to 14.3 MHz?
  964. A.  A mixer
  965. B.  A beat frequency oscillator
  966. C.  A frequency multiplier
  967. D.  A linear translator
  968.  
  969. G8B04 (D) 
  970. What is the name of the stage in a VHF FM transmitter that
  971. selects a harmonic of an HF signal to reach the desired operating
  972. frequency?
  973. A.  Mixer
  974. B.  Reactance modulator
  975. C.  Preemphasis network
  976. D.  Multiplier
  977.  
  978. G8B05 (C) 
  979. Why isn't frequency modulated (FM) phone used below 29.5 MHz?
  980. A.  The transmitter efficiency for this mode is low
  981. B.  Harmonics could not be attenuated to practical levels
  982. C.  The bandwidth would exceed FCC limits
  983. D.  The frequency stability would not be adequate
  984.  
  985. G8B06 (D) 
  986. What is the total bandwidth of an FM-phone transmission having a
  987. 5-kHz deviation and a 3-kHz modulating frequency?
  988. A.  3 kHz
  989. B.  5 kHz
  990. C.  8 kHz
  991. D.  16 kHz
  992.  
  993. G8B07 (B) 
  994. What is the frequency deviation for a 12.21-MHz
  995. reactance-modulated oscillator in a 5-kHz deviation, 146.52-MHz
  996. FM-phone transmitter?
  997. A.  41.67 Hz
  998. B.  416.7 Hz
  999. C.  5 kHz
  1000. D.  12 kHz
  1001.  
  1002. G8B08 (C) 
  1003. How is frequency shift related to keying speed in an FSK signal?
  1004. A.  The frequency shift in hertz must be at least four times the
  1005. keying speed in WPM
  1006. B.  The frequency shift must not exceed 15 Hz per WPM of keying
  1007. speed
  1008. C.  Greater keying speeds require greater frequency shifts
  1009. D.  Greater keying speeds require smaller frequency shifts
  1010.  
  1011. G8B09 (B) 
  1012. What do RTTY, Morse code, AMTOR and packet communications have in
  1013. common?
  1014. A.  They are multipath communications
  1015. B.  They are digital communications
  1016. C.  They are analog communications
  1017. D.  They are only for emergency communications
  1018.  
  1019. G8B10 (C) 
  1020. What is the duty cycle required of a transmitter when sending
  1021. Mode B (FEC) AMTOR?
  1022. A.  50%
  1023. B.  75%
  1024. C.  100%
  1025. D.  125%
  1026.  
  1027. G8B11 (D) 
  1028. In what segment of the 20-meter band are most AMTOR operations
  1029. found?
  1030. A.  At the bottom of the slow-scan TV segment, near 14.230 MHz
  1031. B.  At the top of the SSB phone segment, near 14.325 MHz
  1032. C.  In the middle of the CW segment, near 14.100 MHz
  1033. D.  At the bottom of the RTTY segment, near 14.075 MHz
  1034.  
  1035. SUBELEMENT G9 - ANTENNAS AND FEED LINES [4 exam questions - 4
  1036. groups]
  1037.  
  1038. G9A  Yagi antennas - physical dimensions, impedance matching
  1039. radiation patterns, directivity and major lobes
  1040.  
  1041. G9A01 (A) 
  1042. How can the SWR bandwidth of a parasitic beam antenna be
  1043. increased?
  1044. A.  Use larger diameter elements
  1045. B.  Use closer element spacing
  1046. C.  Use traps on the elements
  1047. D.  Use tapered-diameter elements
  1048.  
  1049. G9A02 (B) 
  1050. Approximately how long is the driven element of a Yagi antenna
  1051. for 14.0 MHz?
  1052. A.  17 feet
  1053. B.  33 feet
  1054. C.  35 feet
  1055. D.  66 feet
  1056.  
  1057. G9A03 (B) 
  1058. Approximately how long is the director element of a Yagi antenna
  1059. for 21.1 MHz?
  1060. A.  42 feet
  1061. B.  21 feet
  1062. C.  17 feet
  1063. D.  10.5 feet
  1064.  
  1065. G9A04 (C) 
  1066. Approximately how long is the reflector element of a Yagi antenna
  1067. for 28.1 MHz?
  1068. A.  8.75 feet
  1069. B.  16.6 feet
  1070. C.  17.5 feet
  1071. D.  35 feet
  1072.  
  1073. G9A05 (B) 
  1074. Which statement about a three-element Yagi antenna is true?
  1075. A.  The reflector is normally the shortest parasitic element
  1076. B.  The director is normally the shortest parasitic element
  1077. C.  The driven element is the longest parasitic element
  1078. D.  Low feed-point impedance increases bandwidth
  1079.  
  1080. G9A06 (A) 
  1081. What is one effect of increasing the boom length and adding
  1082. directors to a Yagi antenna?
  1083. A.  Gain increases
  1084. B.  SWR increases
  1085. C.  Weight decreases
  1086. D.  Windload decreases
  1087.  
  1088. G9A07 (D) 
  1089. What are some advantages of a Yagi with wide element spacing?
  1090. A.  High gain, lower loss and a low SWR
  1091. B.  High front-to-back ratio and lower input resistance
  1092. C.  Shorter boom length, lower weight and wind resistance
  1093. D.  High gain, less critical tuning and wider bandwidth
  1094.  
  1095. G9A08 (C) 
  1096. Why is a Yagi antenna often used for radio communications on the
  1097. 20-meter band?
  1098. A.  It provides excellent omnidirectional coverage in the
  1099. horizontal plane
  1100. B.  It is smaller, less expensive and easier to erect than a
  1101. dipole or vertical antenna
  1102. C.  It helps reduce interference from other stations off to the
  1103. side or behind
  1104. D.  It provides the highest possible angle of radiation for the
  1105. HF bands
  1106.  
  1107. G9A09 (C) 
  1108. What does "antenna front-to-back ratio" mean in reference to a
  1109. Yagi antenna?
  1110. A.  The number of directors versus the number of reflectors
  1111. B.  The relative position of the driven element with respect to
  1112. the reflectors and directors
  1113. C.  The power radiated in the major radiation lobe compared to
  1114. the power radiated in exactly the opposite direction
  1115. D.  The power radiated in the major radiation lobe compared to
  1116. the power radiated 90 degrees away from that direction
  1117.  
  1118. G9A10 (C) 
  1119. What is the "main lobe" of a Yagi antenna radiation pattern?
  1120. A.  The direction of least radiation from the antenna
  1121. B.  The point of maximum current in a radiating antenna element
  1122. C.  The direction of maximum radiated field strength from the
  1123. antenna
  1124. D.  The maximum voltage standing wave point on a radiating
  1125. element
  1126.  
  1127. G9A11  (A)
  1128. What is a good way to get maximum performance from a Yagi
  1129. antenna?
  1130. A.  Optimize the lengths and spacing of the elements
  1131. B.  Use RG-58 feed line
  1132. C.  Use a reactance bridge to measure the antenna performance
  1133. from each direction around the antenna
  1134. D.  Avoid using towers higher than 30 feet above the ground
  1135.  
  1136. G9B  Loop antennas - physical dimensions, impedance matching,
  1137. radiation patterns, directivity and major lobes
  1138.  
  1139. G9B01 (B) 
  1140. Approximately how long is each side of a cubical-quad antenna
  1141. driven element for 21.4 MHz?
  1142. A.  1.17 feet
  1143. B.  11.7 feet
  1144. C.  47 feet
  1145. D.  469 feet
  1146.  
  1147. G9B02 (A) 
  1148. Approximately how long is each side of a cubical-quad antenna
  1149. driven element for 14.3 MHz?
  1150. A.  17.6 feet
  1151. B.  23.4 feet
  1152. C.  70.3 feet
  1153. D.  175 feet
  1154.  
  1155. G9B03 (B) 
  1156. Approximately how long is each side of a cubical-quad antenna
  1157. reflector element for 29.6 MHz?
  1158. A.  8.23 feet
  1159. B.  8.7 feet
  1160. C.  9.7 feet
  1161. D.  34.8 feet
  1162.  
  1163. G9B04 (B) 
  1164. Approximately how long is each leg of a symmetrical delta-loop
  1165. antenna driven element for 28.7 MHz?
  1166. A.  8.75 feet
  1167. B.  11.7 feet
  1168. C.  23.4 feet
  1169. D.  35 feet
  1170.  
  1171. G9B05 (C) 
  1172. Approximately how long is each leg of a symmetrical delta-loop
  1173. antenna driven element for 24.9 MHz?
  1174. A.  10.99 feet
  1175. B.  12.95 feet
  1176. C.  13.45 feet
  1177. D.  40.36 feet
  1178.  
  1179. G9B06 (C) 
  1180. Approximately how long is each leg of a symmetrical delta-loop
  1181. antenna reflector element for 14.1 MHz?
  1182. A.  18.26 feet
  1183. B.  23.76 feet
  1184. C.  24.35 feet
  1185. D.  73.05 feet
  1186.  
  1187. G9B07 (A) 
  1188. Which statement about two-element delta loops and quad antennas
  1189. is true?
  1190. A.  They compare favorably with a three-element Yagi
  1191. B.  They perform poorly above HF
  1192. C.  They perform very well only at HF
  1193. D.  They are effective only when constructed using insulated wire
  1194.  
  1195. G9B08 (C)
  1196. Compared to a dipole antenna, what are the directional radiation
  1197. characteristics of a cubical-quad antenna?
  1198. A.  The quad has more directivity in the horizontal plane but
  1199. less directivity in the vertical plane
  1200. B.  The quad has less directivity in the horizontal plane but
  1201. more directivity in the vertical plane
  1202. C.  The quad has more directivity in both horizontal and vertical
  1203. planes
  1204. D.  The quad has less directivity in both horizontal and vertical
  1205. planes
  1206.  
  1207. G9B09 (D) 
  1208. Moving the feed point of a multielement quad antenna from a side
  1209. parallel to the ground to a side perpendicular to the ground will
  1210. have what effect?
  1211. A.  It will significantly increase the antenna feed-point
  1212. impedance
  1213. B.  It will significantly decrease the antenna feed-point
  1214. impedance
  1215. C.  It will change the antenna polarization from vertical to
  1216. horizontal
  1217. D.  It will change the antenna polarization from horizontal to
  1218. vertical
  1219.  
  1220. G9B10 (C) 
  1221. What does the term "antenna front-to-back ratio" mean in
  1222. reference to a delta-loop antenna?
  1223. A.  The number of directors versus the number of reflectors
  1224. B.  The relative position of the driven element with respect to
  1225. the reflectors and directors
  1226. C.  The power radiated in the major radiation lobe compared to
  1227. the power radiated in exactly the opposite direction
  1228. D.  The power radiated in the major radiation lobe compared to
  1229. the power radiated 90 degrees away from that direction
  1230.  
  1231. G9B11 (C) 
  1232. What is the "main lobe" of a delta-loop antenna radiation
  1233. pattern?
  1234. A.  The direction of least radiation from an antenna
  1235. B.  The point of maximum current in a radiating antenna element
  1236. C.  The direction of maximum radiated field strength from the
  1237. antenna
  1238. D.  The maximum voltage standing wave point on a radiating
  1239. element
  1240.  
  1241. G9C  Random wire antennas - physical dimensions, impedance
  1242. matching, radiation patterns, directivity and major lobes;
  1243. feedpoint impedance of 1/2-wavelength dipole and 1/4-wavelength
  1244. vertical antennas
  1245.  
  1246. G9C01 (A) 
  1247. What type of multiband transmitting antenna does NOT require a
  1248. feed line?
  1249. A.  A random-wire antenna
  1250. B.  A triband Yagi antenna
  1251. C.  A delta-loop antenna
  1252. D.  A Beverage antenna
  1253.  
  1254. G9C02 (D) 
  1255. What is one advantage of using a random-wire antenna?
  1256. A.  It is more efficient than any other kind of antenna
  1257. B.  It will keep RF energy out of your station
  1258. C.  It doesn't need an impedance matching network
  1259. D.  It is a multiband antenna
  1260.  
  1261. G9C03 (B) 
  1262. What is one disadvantage of a random-wire antenna?
  1263. A.  It must be longer than 1 wavelength
  1264. B.  You may experience RF feedback in your station
  1265. C.  It usually produces vertically polarized radiation
  1266. D.  You must use an inverted-T matching network for multiband
  1267. operation
  1268.  
  1269. G9C04 (D) 
  1270. What is an advantage of downward sloping radials on a
  1271. ground-plane antenna?
  1272. A.  It lowers the radiation angle
  1273. B.  It brings the feed-point impedance closer to 300 ohms
  1274. C.  It increases the radiation angle
  1275. D.  It brings the feed-point impedance closer to 50 ohms
  1276.  
  1277. G9C05 (B) 
  1278. What happens to the feed-point impedance of a ground-plane
  1279. antenna when its radials are changed from horizontal to downward-
  1280. sloping?
  1281. A.  It decreases
  1282. B.  It increases
  1283. C.  It stays the same
  1284. D.  It approaches zero
  1285.  
  1286. G9C06 (A) 
  1287. What is the low-angle radiation pattern of an ideal
  1288. half-wavelength dipole HF antenna installed parallel to the
  1289. earth?
  1290. A.  It is a figure-eight at right angles to the antenna
  1291. B.  It is a figure-eight off both ends of the antenna
  1292. C.  It is a circle (equal radiation in all directions)
  1293. D.  It is two smaller lobes on one side of the antenna, and one
  1294. larger lobe on the other side
  1295.  
  1296. G9C07 (B) 
  1297. How does antenna height affect the horizontal (azimuthal)
  1298. radiation pattern of a horizontal dipole HF antenna?
  1299. A.  If the antenna is too high, the pattern becomes unpredictable
  1300. B.  If the antenna is less than one-half wavelength high,
  1301. reflected radio waves from the ground significantly distort the
  1302. pattern
  1303. C.  Antenna height has no effect on the pattern
  1304. D.  If the antenna is less than one-half wavelength high,
  1305. radiation off the ends of the wire is eliminated
  1306.  
  1307. G9C08 (D) 
  1308. If a slightly shorter parasitic element is placed 0.1 wavelength
  1309. away from an HF dipole antenna, what effect will this have on the
  1310. antenna's radiation pattern?
  1311. A.  The radiation pattern will not be affected
  1312. B.  A major lobe will develop in the horizontal plane, parallel
  1313. to the two elements
  1314. C.  A major lobe will develop in the vertical plane, away from
  1315. the ground
  1316. D.  A major lobe will develop in the horizontal plane, toward the
  1317. parasitic element
  1318.  
  1319. G9C09 (B) 
  1320. If a slightly longer parasitic element is placed 0.1 wavelength
  1321. away from an HF dipole antenna, what effect will this have on the
  1322. antenna's radiation pattern?
  1323. A.  The radiation pattern will not be affected
  1324. B.  A major lobe will develop in the horizontal plane, away from
  1325. the parasitic element, toward the dipole
  1326. C.  A major lobe will develop in the vertical plane, away from
  1327. the ground
  1328. D.  A major lobe will develop in the horizontal plane, parallel
  1329. to the two elements
  1330.  
  1331. G9C10 (B) 
  1332. Where should the radial wires of a ground-mounted vertical
  1333. antenna system be placed?
  1334. A.  As high as possible above the ground
  1335. B.  On the surface or buried a few inches below the ground
  1336. C.  Parallel to the antenna element
  1337. D.  At the top of the antenna
  1338.  
  1339.  
  1340. *** We (ARRL) Recommend - Do Not Use The Following Question ***
  1341.  
  1342. G9C11 (D) 
  1343. If you are transmitting from a ground-mounted vertical antenna,
  1344. which of the following is an important reason for people to
  1345. stay away from it?
  1346. A.  To avoid skewing the radiation pattern
  1347. B.  To avoid changes to the antenna feed-point impedance
  1348. C.  To avoid excessive grid current
  1349. D.  To avoid exposure to RF radiation
  1350.  
  1351. ******************************************
  1352.  
  1353.  
  1354. G9D  Popular antenna feed lines - characteristic impedance and
  1355. impedance matching; SWR calculations
  1356.  
  1357. G9D01 (A) 
  1358. What factors determine the characteristic impedance of a
  1359. parallel-conductor antenna feed line?
  1360. A.  The distance between the centers of the conductors and the
  1361. radius of the conductors
  1362. B.  The distance between the centers of the conductors and the
  1363. length of the line
  1364. C.  The radius of the conductors and the frequency of the signal
  1365. D.  The frequency of the signal and the length of the line
  1366.  
  1367. G9D02 (B) 
  1368. What is the typical characteristic impedance of coaxial cables
  1369. used for antenna feed lines at amateur stations?
  1370. A.  25 and 30 ohms
  1371. B.  50 and 75 ohms
  1372. C.  80 and 100 ohms
  1373. D.  500 and 750 ohms
  1374.  
  1375. G9D03 (D) 
  1376. What is the characteristic impedance of flat-ribbon TV-type
  1377. twinlead?
  1378. A.  50 ohms
  1379. B.  75 ohms
  1380. C.  100 ohms
  1381. D.  300 ohms
  1382.  
  1383. G9D04 (C) 
  1384. What is the typical cause of power being reflected back down an
  1385. antenna feed line?
  1386. A.  Operating an antenna at its resonant frequency
  1387. B.  Using more transmitter power than the antenna can handle
  1388. C.  A difference between feed-line impedance and antenna
  1389. feed-point impedance
  1390. D.  Feeding the antenna with unbalanced feed line
  1391.  
  1392. G9D05 (D) 
  1393. What must be done to prevent standing waves of voltage and
  1394. current on an antenna feed line?
  1395. A.  The antenna feed point must be at DC ground potential
  1396. B.  The feed line must be cut to an odd number of electrical
  1397. quarter-wavelengths long
  1398. C.  The feed line must be cut to an even number of physical half-
  1399. wavelengths long
  1400. D.  The antenna feed-point impedance must be matched to the
  1401. characteristic impedance of the feed line
  1402.  
  1403. G9D06 (C) 
  1404. If a center-fed dipole antenna is fed by parallel-conductor feed
  1405. line, how would an inductively coupled matching network be used
  1406. between the two?
  1407. A.  It would not normally be used with parallel-conductor feed
  1408. lines
  1409. B.  It would be used to increase the SWR to an acceptable level
  1410. C.  It would be used to match the unbalanced transmitter output
  1411. to the balanced parallel-conductor feed line
  1412. D.  It would be used at the antenna feed point to tune out the
  1413. radiation resistance
  1414.  
  1415. G9D07 (A) 
  1416. If a 160-meter signal and a 2-meter signal pass through the same
  1417. coaxial cable, how will the attenuation of the two signals
  1418. compare?
  1419. A.  It will be greater at 2 meters
  1420. B.  It will be less at 2 meters
  1421. C.  It will be the same at both frequencies
  1422. D.  It will depend on the emission type in use
  1423.  
  1424. G9D08 (D) 
  1425. In what values are RF feed line losses usually expressed?
  1426. A.  Bels/1000 ft
  1427. B.  dB/1000 ft
  1428. C.  Bels/100 ft
  1429. D.  dB/100 ft
  1430.  
  1431. G9D09 (A) 
  1432. What standing-wave-ratio will result from the connection of a
  1433. 50-ohm feed line to a resonant antenna having a 200-ohm
  1434. feed-point impedance?
  1435. A.  4:1
  1436. B.  1:4
  1437. C.  2:1
  1438. D.  1:2
  1439.  
  1440. G9D10 (D) 
  1441. What standing-wave-ratio will result from the connection of a
  1442. 50-ohm feed line to a resonant antenna having a 10-ohm feed-point
  1443. impedance?
  1444. A.  2:1
  1445. B.  50:1
  1446. C.  1:5
  1447. D.  5:1
  1448.  
  1449. G9D11 (D) 
  1450. What standing-wave-ratio will result from the connection of a
  1451. 50-ohm feed line to a resonant antenna having a 50-ohm feed-point
  1452. impedance?
  1453. A.  2:1
  1454. B.  50:50
  1455. C.  0:0
  1456. D.  1:1
  1457.